Want to buy or sell something? Check the classifieds
  • The Fedora Lounge is supported in part by commission earning affiliate links sitewide. Please support us by using them. You may learn more here.

DaveProc

I'll Lock Up
Messages
4,522
Location
Rhode Island
Hello, I must admit I've been a lurker here for over a year (I think) but have as of yet (unless my aging memory fails me) posted a New Member Hello.

I've enjoyed hats for many years but only been a true 'Addict' for the last couple years, and in that time I've horded (much to my wife's chagrin) over 100 fedoras in fur, wool and straw types and even a few flat caps and ladies vintage hats. I also greatly enjoy restoring hats, when I can, as well as building new hat storage solutions, namely the oval vintage looking boxes in singles or 5 hat towers. I've searched here (albeit minimally) for a thread where others are creating boxes but have as of yet to find much in the way of new creations. I'm sure it must exist in a wonderfully enourmous site such as this, so I'm sure I will find it eventually but if anyone knows of a thread, I'd appreciate a link.

A little about me: I'm in my upper 50's, I work in a locked mental health unit, overnights, and have for nearly 16 years. In the past 2 years I've switched my "overnight projects" to that of messing with the hats I've acquired. I don't usually have a ton of money to spend on new hats so often will buy the bottom of the barrel and see what I can do with them.

Here's just an example of what I did with the hat you see me wearing in my profile picture. The straw boater was found at a local thrift shop for $2.25. the crown was crushed in and there were several spots where the straw was just missing. The leather sweatband, although included, was detached and the reed and reed tape were shot. So, I thought I'd try to used a ladder type such as I had seen in the Ponte Rialto boaters. I couldn't find the necessary ladder insertion tape so I cannibalized some lace trim and used just the ladder type portion of that to re-attache the sweatband and after straightening the crown, and reinforcing the whole thing with some book binding PVA adhesive I had on hand, and finally adding some rafia straw I found at a thrift shop to fill in the holes, I had something I was happy to wear out.

I also included a couple of shots of boxes I've made.

Thank you all for the opportunity to share.
Welcome!
Nice work.
 

TechDawg

New in Town
Messages
6
Looks good to me, though I don't know much about hat repair. I'd like to hear more about these boxes.
Here are a few images of the box types I've done. The Mallory box was the first I made specifically for the hat shown. I modeled it after a vintage Stetson oval box in terms of dimensions other than it's 8" tall instead of the more common 7".

The white box is a 5 hat holder. For the multi hat holder I'm using foam core poster board for the platforms and for all of the rest of the construction I've been using "Builder Board" which I picked up from Menards home center. It's a floor protector that contractors use to cover existing flooring to protect it from damage. It's about the same thickness as the old cardboard in vintage boxes plus has a bit of a moisture barrier built in. I use contact cement to join ends, and a PH neutral, archive quality book binding PVA adhesive to adhere the rims to the lid and the bottom lid which gets permanently affixed to the bottom.

The graphics on the white box are cartoon images of my sheepadoodle, Gertrude, wearing different hats as well as a crest I made with all three of our dogs to emulate some of the crests seen on various hat boxes.

Not sure this thread us the best for more in depth conversation on this so perhaps I'll organize a more informative set of images and details and start a new post in a more appropriate area, whereever that may be.

Thank you everyone for the very kind welcome!
 

Attachments

  • 20261117_075144-COLLAGE.jpg
    20261117_075144-COLLAGE.jpg
    1.6 MB · Views: 1
  • 20261117_075318-COLLAGE.jpg
    20261117_075318-COLLAGE.jpg
    1.3 MB · Views: 1
  • 20261117_075346-COLLAGE.jpg
    20261117_075346-COLLAGE.jpg
    1 MB · Views: 1
  • 20261117_075416-COLLAGE.jpg
    20261117_075416-COLLAGE.jpg
    1.1 MB · Views: 1

Judgmentalist

One Too Many
Messages
1,187
Here are a few images of the box types I've done. The Mallory box was the first I made specifically for the hat shown. I modeled it after a vintage Stetson oval box in terms of dimensions other than it's 8" tall instead of the more common 7".

The white box is a 5 hat holder. For the multi hat holder I'm using foam core poster board for the platforms and for all of the rest of the construction I've been using "Builder Board" which I picked up from Menards home center. It's a floor protector that contractors use to cover existing flooring to protect it from damage. It's about the same thickness as the old cardboard in vintage boxes plus has a bit of a moisture barrier built in. I use contact cement to join ends, and a PH neutral, archive quality book binding PVA adhesive to adhere the rims to the lid and the bottom lid which gets permanently affixed to the bottom.

The graphics on the white box are cartoon images of my sheepadoodle, Gertrude, wearing different hats as well as a crest I made with all three of our dogs to emulate some of the crests seen on various hat boxes.

Not sure this thread us the best for more in depth conversation on this so perhaps I'll organize a more informative set of images and details and start a new post in a more appropriate area, whereever that may be.

Thank you everyone for the very kind welcome!

No idea where an appropriate place would be, but I think this is very cool. I am constantly annoyed by the lack of a couple more decent hat boxes for my favorite hats and I hadn’t thought to make them myself.
 

Forum statistics

Threads
115,876
Messages
3,200,776
Members
59,438
Latest member
lermas ulayao
Top